Sản phẩm
Blue Star E&E
DR SYSTEMS
IDK
iX Cameras
Jireh
MFE Enterprises
NOVO DR
Olympus
SPECTRO-UV
Talcyon
VAST
ZChem
Chụp ảnh phóng xạ (RT, CR, DR)
Dòng điện xoáy (ET, ECT, ECA)
Huỳnh quang tia X (XRF)
Nhiễu xạ tia X (XRD)
Phân tích rung động (VA)
Phát xạ âm (AE)
Quan sát hình ảnh (VT, RVI)
Siêu âm (UT, AUT, PAUT, ToFD, TFM, IRIS)
Thẩm thấu lỏng (PT)
Từ tính (MT)
Tự động hóa
Ứng dụng
Hỗ trợ
Dịch vụ
Đào tạo NDT
Tư vấn bậc 3 về NDT
Hiệu chuẩn thiết bị
Sửa chữa thiết bị
Cho thuê thiết bị
Học NDT
Thuật ngữ
Tiêu chuẩn và các chỉ dẫn kỹ thuật
Kiến thức và Hướng dẫn
Diễn đàn VISCO
Tường thuật
Tải về
Phần mềm
Catalog
Hướng dẫn
Video
Blog
Liên hệ
Sức mạnh đến từ sự mềm dẻo
Các ống cong, khuỷu ống dễ bị hư hại từ các tác động như ăn mòn do dòng chảy tăng tốc (FAC) nhưng việc kiểm tra chúng là một thách thức vì hình dạng của các ống elbow thay đổi từ lồi sang lõm cũng như có nhiều đường kính ống khác nhau. Khi kết hợp với nêm nước, giải pháp này có thể được sử dụng để thu thập dữ liệu trên các đoạn ống khuỷu tay và ống cong với đường kính từ 4,5 in. OD trở lên với nhiều ưu điểm:
- Quét 100% ống elbow
- Hình ảnh 2D C-scan trực quan
- Dữ liệu thu có mật độ cao (1 mm × 1 mm)
- Đo, kiểm tranh, lập bản đồ ăn mòn nhanh độ dày thành ống elbow
Dữ liệu có độ phân giải cao
Bộ quét được thiết kế đế sử dụng với OmniScan® MX2 hay SX để phát hiện và đo lường các hư hại hoặc bất thường như đo chiều dày ống còn lại, ăn mòn pitting hay tách lớp trong thành ống. Dữ liệu độ phân giải cao kết hợp với các chế độ hiển thị khác nhau trên thiết bị hoặc trên máy tính (cần OmniPC™ ) cung cấp hình ảnh rõ ràng về tình trạng của các ống elbow giúp việc giải đoán dễ dàng và chính xác hơn.
- Các trục quét và lưu dữ liệu được mã hóa theo vị trí và có thể thay đổi sử dụng một nút bấm trên bộ quét để thay đổi vị trí dữ liệu một cách dễ dàng.
- Bánh xe từ giữ bộ quét chắc chắn bám vào bề mặt ống, trong khi gioăng bằng xốp tiếp xúc theo bề mặt cong và giữ cột nước bên trong.
- Việc sử dụng cột nước làm chất tiếp âm giúp bề mặt có thể dễ dàng phù hợp với cả mặt lồi và lõm trên ống cong, thiết bị và phần mềm trên OmniScan đồng bộ dữ liệu bề mặt với chiều dày đo được.
- Các nêm khác nhau được thiết kế để phù hợp với các đường kính ống khác nhau. Gắn đầu dò và nêm phù hợp lên bộ quét là bạn đã sẵn sàng cho công việc.
Quét dọc ống
Cấu hình quét ống này rất hữu dụng khi kiểm tra các ống nhỏ hay khi vùng cần quét tập trung vào một vùng của ống (dưới đáy và mặt trên). Bộ quét ống elbow FlexoFORM khi sử dụng để quét dọc ống sẽ giúp tăng tốc độ kiểm tra lên hàng chục lần.
Quét ống elbow nhỏ
Các nêm bán tự động được thiết kế phù hợp với ống nhỏ từ 101 mm (4.5 in) trở lên. Ở chế độ quét thủ công, có thể kiểm tra vùng bên ngoài (mặt cong ngoài) của các ống elbow có đường kính từ 1.3 in. OD tới 4 in. OD hoặc quét dọc ống để thu được hình ảnh mã hóa C-scans. Các nêm SFA1-SMALL cho ống nhỏ cần kết hợp với Mini-Wheel™ encoder.
Quét tự động
Trong vài ứng dụng cần quét dọc ống thay vì quét vòng quanh ống, nêm SFA1-AUTO phù hợp bộ quét tự động cho các ống từ 220mm (8.625 in.) OD trở lên.
Thông tin đặt hàng/Ordering info
| Mã | Tên sản phẩm | Mô tả/Description |
| Q7500062 | FlexoFORM | FlexoFORM package with probe and one (1) SFA1 water wedge for 8.625 in. outside diameter. 5 m long cables compatible with current generation of OmniScan and Focus instruments. |
| Q7500063 | FlexoFORM-Kit | FlexoFORM package with probe and six (6) SFA1 water wedges (for 4.5 in., 6.625 in., 8.625 in., 10.75 in., 12.75 in., and 16 in. outside diameters). 5 m long cables compatible with current generation of OmniScan and Focus instruments. |
| Q3301202 | 7.5L64-64X7-FA1-P-5-OM | Flexible phased array probe, 7.5 MHz, 64 elements, 1 mm pitch, 7 mm elevation, FA1 case type for the FlexoFORM scanner (SFA1-FLEXO), SFA1-SMALL and SFA1-AUTO wedge series, 5 m cable length, and OmniScan connector. |
| Q7500067 | SFA1-Flexo-OD4.5 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 4.5 inches (114 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500068 | SFA1-Flexo-OD5.563 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 5.563 inches (141 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500069 | SFA1-Flexo-OD6.625 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 6.625 inches (168 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500070 | SFA1-Flexo-OD8.625 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 8.625 inches (219 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500071 | SFA1-Flexo-OD10.75 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 8.625 inches (219 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500072 | SFA1-Flexo-OD12.75 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 12.75 inches (324 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500073 | SFA1-Flexo-OD14 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 14 inches (356 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500074 | SFA1-Flexo-OD16 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 16 inches (406 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500075 | SFA1-Flexo-OD18 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 18 inches (457 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500076 | SFA1-Flexo-OD20 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 20 inches (508 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500077 | SFA1-Flexo-OD22 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 22 inches (559 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500078 | SFA1-Flexo-OD24 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 24 inches (610 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500079 | SFA1-Flexo-OD26 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 26 inches (660 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500080 | SFA1-Flexo-OD28 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 28 inches (711 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500081 | SFA1-Flexo-OD30 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 30 inches (762 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500082 | SFA1-Flexo-OD32 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 32 inches (813 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500083 | SFA1-Flexo-OD34 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 34 inches (864 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500084 | SFA1-Flexo-OD36 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 36 inches (914 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500085 | SFA1-Flexo-OD42 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 42 inches (1067 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500086 | SFA1-Flexo-OD48 | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 48 inches (1219 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7500087 | SFA1-Flexo-Flat | Standard wedge for Flexible array probe FA1 and compatible with FlexoFORM scanner. The wedge is used to generate 0° Longitudinal Waves and features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. |
| Q7790124 | SFA1-SMALL-KIT-FULL | Kit of 7x SFA1-SMALL water wedge probe holders, 1x FA1 flexible phased array probe and 1x ENC1 mini-wheel encoder with magnetic wheel. Wedge diameters are compatible with 1.3, 1.66, 1.9, 2.375, 2.875, 3.5 and 4 inches outside diameter pipes and elbow extrados. The flexible PA probe is 7.5MHz, 64 elements, 7mm elevation, 1mm pitch, for a total apperture length of 64mm. The kit also includes irrigation tube and cable protection sleeve. Cable lenghts are 5m. The probe and encoder are compatible with current generation of phased array instruments (Lemo and OM connectors). All packaged in hard carrying case. |
| Q7790125 | SFA1-SMALL-KIT | Kit of 7x SFA1-SMALL water wedge probe holders. Wedge diameters are compatible with 1.3, 1.66, 1.9, 2.375, 2.875, 3.5 and 4 inches outside diameter pipes and elbow extrados. The kit also includes irrigation tube and cable protection sleeve. Cable lenghts are 5m. All packaged in hard carrying case. |
| Q7500088 | SFA1-Auto-OD8.625 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 8.625 inches (219 mm) Outside Diameter (OD) for inspection of extrados and intrados of pipe elbows. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500089 | SFA1-Auto-OD10.75 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 10.75 inches (273 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500090 | SFA1-Auto-OD12.75 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 12.75 inches (324 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500091 | SFA1-Auto-OD14 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 14 inches (356 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500092 | SFA1-Auto-OD16 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 16 inches (406 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500093 | SFA1-Auto-OD18 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 18 inches (457 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500094 | SFA1-Auto-OD20 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 20 inches (508 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500095 | SFA1-Auto-OD22 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 22 inches (559 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500096 | SFA1-Auto-OD24 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 24 inches (610 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500097 | SFA1-Auto-OD26 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 26 inches (660 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500098 | SFA1-Auto-OD28 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 28 inches (711 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500099 | SFA1-Auto-OD30 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 30 inches (762 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500100 | SFA1-Auto-OD32 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 32 inches (813 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500101 | SFA1-Auto-OD34 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 34 inches (864 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500102 | SFA1-Auto-OD36 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 36 inches (914 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500103 | SFA1-Auto-OD42 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 42 inches (1067 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500104 | SFA1-Auto-OD48 | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 48 inches (1219 mm) Outside Diameter (OD) for inspection of pipes. The wedge also features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not Compatible with FlexoFORM scanner. |
| Q7500105 | SFA1-Auto-Flat | Standard wedge for Flexible array probe FA1 and compatible with MapROVER and SteerROVER scanners. The wedge is used to generate 0° Longitudinal Waves and features an 9 mm high water column allowing inspection of up to 30 mm thick carbon steel materials. Not compatible with FlexoFORM scanner. |
| Q7500106 | SFA1-Small-OD1.3 | Standard wedge for Flexible array probe FA1 for manual inspection of small pipes or elbow extrados (not compatible with elbow intrados). The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 1.315 inches (33.4 mm) Outside Diameter (OD) for inspection of elbow extrados. The wedge also features an 11 mm high water column allowing inspection of up to 35 mm thick carbon steel materials. Compatible with the Mini-Wheel encoder. Not compatible with FlexoFORM scanner. |
| Q7500107 | SFA1-Small-OD1.66 | Standard wedge for Flexible array probe FA1 for manual inspection of small pipes or elbow extrados (not compatible with elbow intrados). The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 1.66 inches (42 mm) Outside Diameter (OD) for inspection of elbow extrados. The wedge also features an 11 mm high water column allowing inspection of up to 35 mm thick carbon steel materials. Compatible with the Mini-Wheel encoder. Not compatible with FlexoFORM scanner. |
| Q7500108 | SFA1-Small-OD1.9 | Standard wedge for Flexible array probe FA1 for manual inspection of small pipes or elbow extrados (not compatible with elbow intrados). The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 1.9 inches (48 mm) Outside Diameter (OD) for inspection of elbow extrados. The wedge also features an 11 mm high water column allowing inspection of up to 35 mm thick carbon steel materials. Compatible with the Mini-Wheel encoder. Not compatible with FlexoFORM scanner. |
| Q7500109 | SFA1-Small-OD2.375 | Standard wedge for Flexible array probe FA1 for manual inspection of small pipes or elbow extrados (not compatible with elbow intrados). The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 2.375 inches (60 mm) Outside Diameter (OD) for inspection of elbow extrados. The wedge also features an 11 mm high water column allowing inspection of up to 35 mm thick carbon steel materials. Compatible with the Mini-Wheel encoder. Not compatible with FlexoFORM scanner. |
| Q7500110 | SFA1-Small-OD2.875 | Standard wedge for Flexible array probe FA1 for manual inspection of small pipes or elbow extrados (not compatible with elbow intrados). The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 2.875 inches (73 mm) Outside Diameter (OD) for inspection of elbow extrados. The wedge also features an 11 mm high water column allowing inspection of up to 35 mm thick carbon steel materials. Compatible with the Mini-Wheel encoder. Not compatible with FlexoFORM scanner. |
| Q7500111 | SFA1-Small-OD3.5 | Standard wedge for Flexible array probe FA1 for manual inspection of small pipes or elbow extrados (not compatible with elbow intrados). The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 3.5 inches (89 mm) Outside Diameter (OD) for inspection of elbow extrados. The wedge also features an 11 mm high water column allowing inspection of up to 35 mm thick carbon steel materials. Compatible with the Mini-Wheel encoder. Not compatible with FlexoFORM scanner. |
| Q7500112 | SFA1-Small-OD4 | Standard wedge for Flexible array probe FA1 for manual inspection of small pipes or elbow extrados (not compatible with elbow intrados). The wedge is used to generate 0° Longitudinal Waves and features a curvature matching 4 inches (101.6 mm) Outside Diameter (OD) for inspection of elbow extrados. The wedge also features an 11 mm high water column allowing inspection of up to 35 mm thick carbon steel materials. Compatible with the Mini-Wheel encoder. Not compatible with FlexoFORM scanner. |
